If you run Volvo FH or FM trucks, you already know the air suspension is one of the best things about the truck — until it isn’t. Volvo FH/FM air suspension problems usually start small: a slow overnight lean, a compressor that cycles longer than it used to, or a rear end that feels floaty over expansion joints. Catch them early and you’re looking at a cheap afternoon repair. Ignore them and you’ll be replacing bellows, a worn-out compressor, and a chewed height sensor linkage all at once.
I’ve spent over twenty years working on European trucks in fleet workshops, and Volvos make up a big share of that. The FH/FM platform is genuinely one of the most reliable air suspension setups on the market, but it has its weak points, and they’re predictable. Here’s how the system actually fails, how to diagnose it properly, and what it takes to fix it right.
How the Volvo FH/FM Air Suspension Is Set Up
Before you start troubleshooting, you need a clear picture of what’s bolted to the truck. The current-generation Volvo FH (2012 onward) and FM use a mixed layout that confuses plenty of drivers:
- Front axle: parabolic leaf springs with hydraulic shock absorbers on standard spec trucks — the front of an FH is steel-sprung, not air-sprung.
- Rear axles: four air bellows, two per side, mounted between the axle housing and the chassis side members.
- ECAS: a WABCO-supplied Electronically Controlled Air Suspension, with ride-height sensors on the driven axle, a central ECAS valve block, and an ECU that talks to the truck’s main electrical system.
- Air supply: an engine-driven compressor feeding through an air dryer into the auxiliary circuit, which feeds the bellows. Working pressure in the system sits in the usual 8.5–10 bar range for European commercial vehicles, per the pressure standards UN ECE R13 builds on.
The ECAS is the part that separates a modern Volvo from a twenty-year-old truck. Instead of a purely mechanical levelling valve, height sensors on the axle report ride height to the ECU hundreds of times per second, and the ECU commands the valve block to add or exhaust air. That’s what gives you the kneeling function, the memory heights for loading docks, and automatic height control on the move.
It’s also what creates extra failure points. A worn linkage on a height sensor can do more damage on an ECAS truck than a small bellow leak, because the system will happily pump itself into a twist trying to chase a bogus height reading. Keep that in mind as you work through the faults below.
The 6 Most Common Volvo Air Suspension Problems
1. Leaking Air Bellows
The classic. Air bellows on an FH/FM are rolling-lobe type, and they fail in predictable places: the crimped ring where the rubber meets the metal top plate, the rolling lobe itself, and the base where road grime and salt sit against the rubber year after year.
Realistic lifespan is 300,000–500,000 km or 8–10 years, whichever comes first, and it shortens fast if the truck runs winter routes where de-icing salt is heavy. In my experience, trucks doing regular UK or Scandinavian winter work eat bellows nearly twice as fast as trucks running Iberia.
The tell-tale symptoms: the truck leans after standing overnight, the compressor kicks in more often, and if you run a hand over the bellow you may find a fine crack line or a sticky patch of rubber dust where the bellow is losing air. A hairline leak can be nearly invisible dry — always soap-test.
2. ECAS Height Sensor Failures
Each height sensor is a small rotary potentiometer on the chassis, driven by a linkage rod down to the axle. Two things kill them: the sensor’s internal track wears out and the signal drifts, or — far more common — the linkage ball joints wear sloppy, the rod bends after contact with road debris, and the signal stops telling the truth.
A drifting height sensor doesn’t just park the truck slightly wrong. The ECU will keep trimming air to chase a false reading, which shows up as uneven frame height side-to-side, a truck that won’t hold memory heights, or constant small compressor corrections while driving. You’ll usually find a stored ECAS fault code, but not always — a slowly drifting sensor can stay under the radar while it quietly wrecks your driveline geometry.
3. ECAS Valve Block Problems
The central valve block is the system’s control centre: it fills and exhausts each bellow circuit on command. Internally, the pilot and solenoid valves can stick or leak. A sticking exhaust valve is the usual suspect when a truck drops height slowly overnight even though every bellow passes a soap test — the air is escaping through the valve block itself, not the bellows.
Failed valve blocks also knock out kneeling and memory height functions. If the truck goes up but never comes down (or vice versa), before you start swapping bellows, listen at the valve block with the system working: a stuck solenoid often gives itself away with a weak or absent exhaust hiss where there should be one.
4. Air Dryer and Compressor Trouble
The suspension lives on clean, dry air. When the air dryer’s desiccant saturates, moisture moves downstream, and water in an ECAS valve block is bad news: corrosion, sticky valves, and in freezing weather, ice that blocks air flow entirely. WABCO’s own service guidance for air treatment pushes regular desiccant cartridge replacement — every three years is a sensible interval for a working truck, and many fleets do it annually on trucks that run hard.
The compressor itself wears too. A tired compressor can still build pressure, but it takes longer and pumps more oil vapour into the system, which gunks up the same valves the moisture attacks. Watch the pressure build time from cold; a healthy system on an FH should be charging noticeably within a few minutes of starting. Slow recovery plus oil weeping at the dryer purge is your sign to look at the compressor before it takes out the rest of the system.
5. Air Line and Push-In Fitting Leaks
Between the dryer, the valve block, and four bellows there are metres of nylon air line and a dozen fittings. Each one is a potential leak. The plastic lines rub on chassis brackets over years of vibration until they wear through, and older compression-style fittings lose their grip once the pipe has been re-seated a few times.
These leaks are sneaky because they hide under the cab and along the frame rails. A systematic soap test along the air supply line, the ECAS feed lines, and every fitting — with the system aired up and the truck at working height — finds most of them in twenty minutes.
6. Worn Shocks and Bushings
People forget that an air-sprung axle still needs shock absorbers. The bellows carry the load; the shocks control the movement. When the rear shocks on an FH/FM fade, the symptoms are a boaty rear end, brake dive that feels exaggerated, air bellows that flex through more travel than they should (which shortens their life), and uneven tyre wear starting at the drive axles.
Worn axle bushings and anti-roll bar links stack on top of this: vague handling, clunks over potholes, and a truck that tramlines on rutted motorways. If you’re chasing a full suspension refresh, budget the shocks and bushes together with the bellows — doing bellows alone on a truck with dead shocks just means the new bellows work through a bigger travel range and age faster.
Step-by-Step Troubleshooting Guide
Step 1: The Overnight Lean Test
Park the loaded-as-usual truck on level ground, measure frame height to the ground on both sides, and leave it overnight. Next morning, re-measure. A drop of more than about 10–20 mm on one corner points straight to that corner’s bellow, its feed line, or its valve circuit. A uniform sag on both sides of an axle points at the supply side — dryer purge valve, compressor check valve, or the ECAS valve block.
Step 2: Soap Test Under Load
Soap test with the system at full working pressure, not parked empty. Mix dish soap with water, brush it generously over the entire bellow — pay special attention to the crimp rings top and bottom and the rolling lobe — then the fittings and the valve block. Bubbles take a minute to form on hairline cracks, so be patient. Give every fitting a full minute before you move on.
Step 3: Watch the Compressor Duty Cycle
With the engine at idle, note how long the compressor takes to fill the system from empty after a full purge, and how often it cycles once the system is charged. A system in good shape holds height with the compressor mostly resting. A compressor that’s constantly topping up is telling you air is going somewhere — find it before it tells you by dying at 3 a.m. on a Sunday.
Step 4: Measure Ride Height Against Spec
Check the static ride height at the points Volvo specifies for your exact wheelbase and suspension code — frame rail to ground, both sides, on dead-level ground with the truck loaded as it normally runs. Side-to-side differences over roughly 10 mm wreck driveline angles and tyre wear. If heights are off but stable, the system isn’t leaking; it’s calibrated or mechanically wrong — bent linkage, wrong sensor geometry, or a truck that’s been loaded heavy on one side for so long the driver thinks the lean is normal.
Step 5: Read the Fault Memory with Volvo Tech Tool
The ECAS stores diagnostic trouble codes, and Volvo’s Tech Tool (the factory diagnostic software your Volvo dealer or a well-equipped independent shop runs) reads them, shows live height sensor data, and runs guided tests on the valve block outputs. Comparing live height readings from both sensors while you slowly raise and lower the truck will expose a drifting sensor in minutes. If you run more than a couple of Volvos, getting comfortable with Tech Tool’s ECAS screens pays for itself fast.
Replacing Volvo Air Bellows: What to Expect
Safety first, because this is where people get hurt: the suspension must be fully exhausted and the chassis supported on stands before you undo anything. A bellow with 9 bar behind it is a bomb. Purge the system, support the frame, and confirm the bellows are fully collapsed before you crack a fitting.
With the truck safely supported, a bellow swap on an FH/FM is a straightforward job — typically 1.5–2 hours per corner for a tech who’s done it before, including the soap test afterwards. Always replace bellows in pairs on the same axle. A new bellow next to a tired one sits at a different height under load, and the ECAS will trim itself into a compromise that loads both of them wrong.
On parts: genuine Volvo bellows are made by major OE suppliers — the same names like Continental and Dunlop that supply the factory lines — and good aftermarket units from those same manufacturers perform identically at a noticeably lower price. The trap is ultra-cheap no-name bellows with unbranded rubber; they’re a false economy that starts cracking in two winters. If you’re maintaining more than a couple of trucks, buying bellows, shocks, and suspension bushings by the set saves real money. We supply wholesale air bellows and suspension parts for all the common European platforms — Actros, Scania, FH/FM, TGX, XF — through Snowling Auto Parts; email lwj19999111007@gmail.com or WhatsApp +86 19999111007 for a wholesale quote.
Preventive Maintenance That Actually Works
Air suspension problems on an FH/FM are mostly preventable, and the routine is cheap:
- Wash the bellows whenever you wash the truck, and inspect the rubber for cracks, bulges, and chafing every service. Ten seconds per corner with a torch.
- Replace the air dryer cartridge on a fixed schedule — every three years minimum, annually on trucks doing heavy mileage or winter salt routes. It’s the cheapest insurance the system has.
- Keep the height sensor linkages clean and tight. A shot of water dispersant at service time, and replace ball joints the moment they feel sloppy.
- Drain air tanks weekly (or trust the auto-drain, but check it works). Water in the tanks is water waiting to reach the valves.
- Verify ride height at every service, loaded, on level ground, against the spec for your chassis. You’ll catch a drifting sensor months before it becomes a tyre-wear complaint.
FAQ
How long do air bellows last on a Volvo FH or FM?
Typical lifespan is 300,000–500,000 km or 8–10 years. Trucks running regular winter routes with heavy road salt tend toward the low end; trucks in milder climates and consistent highway work often exceed it. Rather than waiting for a failure, inspect bellows at every service and plan replacement around the ten-year mark even if they still look okay — the rubber hardens with age regardless of kilometres.
Why does my Volvo lean to one side overnight?
Almost always an air leak on that corner: a cracked bellow, a leaking feed line or fitting, or the ECAS valve block exhausting that circuit. Soap-test the corner’s bellow and line first, then listen at the valve block. If both sides of the axle sag evenly, look at the supply side — dryer purge valve, compressor check valve, or a leaking service line.
Can I keep driving with a leaking air bellows?
Not for long, and not with a load. A deflated bellow lets the axle sit off-centre, which hammers driveline components, upsets brake geometry and headlight aim, and can damage the collapsed bellow itself beyond repair. Limp carefully to a workshop with a light or empty load; don’t plan a week of full-load work around it.
How do I recalibrate the ECAS ride height on a Volvo FH?
Through Volvo Tech Tool. With the truck on dead-level ground at normal load, you set the reference height per the procedure for your chassis, and the ECU stores the sensor values as the new baseline. Doing it by eye or by bending linkages gets you a truck that’s consistently wrong in a new direction — the calibration routine takes fifteen minutes when you follow it properly.
Are aftermarket air bellows as good as genuine Volvo parts?
The right aftermarket parts, yes. The OE supply chain for European truck bellows is concentrated in a handful of manufacturers like Continental and Dunlop, and their aftermarket-branded units use the same construction. What to avoid is unbranded ultra-cheap bellows with no traceable manufacturer — the rubber compounds simply don’t last. Buy from a supplier who can tell you who made the part, and pair them with quality shocks.
Keep Your Volvo Riding Level
The FH and FM air suspension is a system that tells you everything you need to know, if you watch it: overnight lean, compressor behaviour, and ride height at service intervals will catch 90% of failures while they’re still one-part jobs. Ignore the early signs and every failed component drags its neighbours down with it.
If you found this guide useful, subscribe to the newsletter for more European truck suspension and parts know-how — practical, workshop-tested, no fluff. And if you’re maintaining a fleet and want wholesale pricing on air bellows, shock absorbers, and suspension parts for Volvo, Mercedes, Scania, MAN, and DAF platforms, get in touch with Snowling Auto Parts at lwj19999111007@gmail.com or WhatsApp +86 19999111007 — tell us what you run and we’ll quote you the same day.